Smoke and fire detection with cameras in production
Author: DuoVision team
For: owners and managers of production sites and warehouses, people responsible for fire safety, health and safety engineers
Cameras in a production area notice smoke and open flame and send a card with a frame, but they do not replace a fire alarm. We configure this for your site and start in shadow mode.
Summary
- Cameras already installed on a production site or in a warehouse can show a responsible person smoke, open flame and someone smoking in a banned zone, with a frame in the card.
- This adds to a fire alarm and does not replace it: fire protection systems in Ukraine are designed and installed under DBN V.2.5-56:2014, and the Fire Safety Rules (MVS order No. 1417) require first-response extinguishing means even where an alarm exists.
- An alarm reacts to smoke at the detector, while a camera sees the scene: a person with a cigarette by the racks, or sparks near welding before any smoke.
- Lighting, steam and dust in food plants cause false alerts, so we set up rules for each camera on your footage before cards go to people.
For: owners and managers of production sites and warehouses, people responsible for fire safety, health and safety engineers
What a camera can notice
Video analytics watches the stream from cameras you already have and sets aside moments worth attention. For fire safety these are three groups of events:
- smoke in the frame: a gray plume above equipment, in an aisle or near racking;
- open flame or bright sparks, for example near welding or grinding;
- smoking in a banned zone: a person with a cigarette near a warehouse, workshop, forklift charging area or fuel tanks.
Each event arrives as a card with a frame, time, camera and zone. Your responsible person decides: a guard, the electrician on duty, a shift manager. We set up the rules for your site and start in shadow mode: first you and we see the cards, and they go to the shift once false alerts are rare.
Why this does not replace a fire alarm
In Ukraine, fire protection systems are designed and installed under DBN V.2.5-56:2014 "Fire protection systems". The Fire Safety Rules of Ukraine, approved by MVS order of 30.12.2014 No. 1417, refer to the same standard: in the section on facility requirements, equipping with fire protection systems is tied to DBN V.2.5-56:2014.
The same Rules say, in the part on extinguishing means, that buildings with fire suppression and fire alarm systems must still keep first-response extinguishing means (s. V, ch. 3, p. 3.6). An alarm does not remove the need for extinguishers, and video analytics does not remove the need for the alarm.
The difference is what each tool sees. An alarm installed under DBN reacts to smoke, temperature or flame at the detector and carries the formal protection of the site. A camera sees the scene: who stands where, what happens near equipment, whether there is smoke or flame in the frame. It can show a person with a cigarette by cardboard racks before anything smolders, and it gives a frame that shows where exactly the fire is.
In the United States, NFPA 72 recognizes video detection of smoke and flame but requires a design based on the specific site, and the engineering firm Jensen Hughes notes that reliability is affected by changing lighting, airflow and the use of the space. We treat video analytics as an extra layer on top of your alarm and do not suggest switching off or replacing what was installed under DBN.
Smoking in banned places
The Fire Safety Rules require the site manager to set smoking places by a written order and mark them with a sign or notice. Smoking outside those places is banned (s. III, ch. 1, p. 1.19).
Someone walking past sees a cigarette by the warehouse gate. A camera looks at any hour, including nights, when few people are on site. We set up the zones where smoking is banned and the time of day. A card with a frame reaches the head of security or of health and safety, and the talk with the employee rests on a fact, not a rumor.
What we account for in setup: light, steam, dust
Smoke and flame on video look like other things, so we tune rules for each camera and do not switch them on the same way everywhere. What we take into account:
- Lighting. A night camera with infrared sees differently from a day one, and glare on a wet floor or sun in a gate can look like flame.
- Steam. In food plants, steam over cooking, washing and scalding areas looks like smoke on video. We either leave such zones out of the smoke rule or set a stricter threshold and a longer hold time.
- Dust and flour in the air, exhaust from vehicles near gates.
- Distance and angle. A small plume far from the camera is not visible, so we choose cameras for this rule from the site plan.
So the first step is this: we take a few days of your footage, run the rule in shadow mode and show what it found and what it mistook for smoke. Only then do cards go to the shift.
How a card reaches the responsible person
A card contains a frame, time, camera and zone and arrives in the panel. For smoke and fire we recommend a separate recipient outside the general flow: the security shift on duty or the site's fire-technical service. The recipient opens the frame, checks on site or through other cameras and acts under your instruction, for example the evacuation plan. The decision to call the fire service is yours, and the camera does not replace it.
All cards stay in a log with the frame and time. That supports an internal review and the conversation with employees. For the personal data side of video monitoring, see the guide on video analytics and personal data.
Where to start
- List the higher-risk zones: welding, forklift battery charging, cardboard and film storage, fuel tanks, electrical rooms, places where smoking has already happened.
- Check which of these zones your cameras cover and from what distance.
- Decide who receives cards at night and on weekends.
- Give us a few days of footage: we will set up the rules for your site and show the result before launch.
A similar approach is described for warehouses, forklifts and pedestrians and PPE control. The general approach to workplace safety is on the workplace safety page. You can discuss your site through contacts.
Where to apply this
- Occupational safety
- Warehousing and logistics
- Food manufacturing
- A camera checks whether a worker wears a mask: food production
- Line and equipment downtime: how to measure it with a camera when there are no sensors or MES
- What FSSC 22000, BRCGS and IFS auditors check on the floor, and the records video monitoring can supply